Vintage audio glossary: tape, repair and hi-fi terms explained
The words that turn up on tape boxes, spec sheets, service manuals and secondhand listings, each explained in a sentence or two. Where a term needs more than that, the definition links to the guide on Capstan that covers it.
Jump to: A · B · C · D · E · G · H · M · N · P · R · S · T · V · W. Last checked: 22 November 2026.
A
- Acetate tape
- Early magnetic tape on a cellulose acetate base, common until the 1960s. It can become brittle and smell of vinegar as it decays; it should never be baked. See the tape transfer guide.
- ATRAC
- Sony's data-reduction code for MiniDisc. Standard (SP) mode uses about 292 kbit/s; later long-play modes use less. See MiniDisc to digital.
- Azimuth
- The angle of the tape head's gap relative to the tape. If playback azimuth does not match the recorder's, high frequencies are lost. Adjusting it by ear or with a test tape is a key step in any tape transfer.
B
- Baking
- Heating a tape suffering from sticky shed at a low, controlled temperature for many hours so that it can be played once more for a transfer. A specialist job for valuable tapes, and never for acetate.
- Bias
- A high-frequency signal added during analogue recording so that the tape responds linearly. Each cassette type needs its own bias setting, which is why decks have Type I, II and IV switches or automatic detection. See the tape formats table.
- Broadcast WAVE (BWF)
- A WAV file with an extra block of descriptive metadata, widely used by archives for master files. See the home archive plan.
C
- Capstan
- The precisely machined spinning shaft that, with the rubber pinch roller pressing the tape against it, pulls the tape past the heads at constant speed. Dual-capstan decks use one on each side of the heads for steadier tension. This journal is named after it.
- Crossover
- The network of capacitors, coils and resistors inside a loudspeaker that sends bass to the woofer and treble to the tweeter. Its capacitors age; see vintage speaker crossovers.
- Cartridge (phono)
- The part at the end of a tonearm that holds the stylus and turns its movement into an electrical signal. Moving-magnet types are the most common; moving-coil types need more gain. See reviving a vintage turntable.
D
- DAT
- Digital Audio Tape, a rotary-head cassette format introduced by Sony in 1987, recording 16-bit PCM at 48, 44.1 or 32 kHz. See getting audio off DAT.
- dbx
- A noise-reduction system that compresses the signal when recording and expands it on playback. A dbx tape must be decoded with dbx; other systems will not do.
- Dolby B, C and S
- Noise-reduction systems that boost quiet high frequencies when recording and cut them on playback, lowering tape hiss. Dolby B was the consumer standard on cassettes; C and S reduce more noise. Decode with the system that was used, and only if one was used.
E
- Electrolytic capacitor
- A capacitor with a liquid or paste electrolyte, used for power-supply filtering and signal coupling. It dries out with age and heat and is the classic wear part of old amplifiers. Large ones can hold a dangerous charge after the plug is pulled: see what fails in vintage hi-fi.
- Equalisation (EQ)
- A standard frequency curve applied on recording and reversed on playback. Tape uses NAB or IEC curves; records use the RIAA curve. A mismatch makes a transfer too bright or too dull.
G
- Ground loop
- A loop formed when two pieces of equipment are connected both through signal cables and through mains earth, letting a small current flow in the shields and causing hum. Never cure it by removing a mains earth. See tracing hum and buzz.
H
- Half-track, quarter-track
- How the width of a ¼-inch tape is divided. Half-track (two-track) uses two wide tracks, typical of studio masters; quarter-track (four-track) uses four narrower tracks, two per direction, typical of home stereo tapes. See buying a reel-to-reel deck.
- Head (tape)
- The electromagnet that records, plays or erases the tape. Three-head decks have separate record and playback heads so you can monitor while recording. Heads wear flat over the years.
M
- MiniDisc
- Sony's 64 mm magneto-optical disc, launched in 1992. NetMD models restricted uploading to a computer; Hi-MD models such as the MZ-RH1 can upload standard discs. See MiniDisc to digital.
N
- NAB and IEC (CCIR)
- The two main open-reel equalisation standards: NAB in North America and Japan, IEC (formerly CCIR) in Europe. NAB is also the name of the large-centre reel hub used on professional 10½-inch reels.
P
- Phono stage (phono preamp)
- The amplifier that raises a phono cartridge's tiny signal to line level and applies RIAA equalisation. Built into many vintage amplifiers; needed as a separate box with most modern ones. See digitising vinyl records.
- Pinch roller
- The rubber wheel that presses the tape against the capstan. When it hardens or glazes, the tape slips and speed wavers; it is a routine replacement part.
R
- Recapping
- Replacing a device's ageing electrolytic capacitors. Useful when done selectively and measured; not a cure-all. See what fails in vintage hi-fi.
- RIAA curve
- The equalisation standard for vinyl records since the 1950s: bass is cut and treble boosted when cutting the record, and the phono stage reverses it. Most 78s predate it and used other curves.
- Rectifier
- The diode or tube that turns mains alternating current into the direct current an amplifier runs on. See vacuum tubes in hi-fi.
S
- Sticky shed
- Binder hydrolysis: the binder that holds the magnetic coating on some 1970s and 1980s tapes absorbs moisture, turns gummy and sheds onto the heads, often with a squeal. Stop playing at once. See the tape transfer guide.
- Surround (speaker)
- The flexible ring joining a woofer's cone to its frame. Foam surrounds crumble after a few decades; see re-foaming a vintage woofer.
- S/PDIF and AES3
- Digital audio connections: S/PDIF on coaxial or optical (Toslink) connectors for consumer gear, AES3 on balanced XLR cables for professional gear. Same basic data, different electrical levels.
T
- Tube (valve)
- A vacuum tube used to amplify a signal or rectify current. Types such as 12AX7, EL34, EL84, KT88 and 300B are common in hi-fi. Tube equipment runs at lethal voltages. See vacuum tubes in hi-fi.
- Type I, II, III, IV
- The IEC classes of cassette tape: ferric, chrome or cobalt, ferrichrome, and metal. See the tape formats table.
V
- VU meter
- A volume-unit meter with a standardised, fairly slow response that shows average level rather than brief peaks. When digitising, watch a peak meter as well, since short peaks can clip a digital recording that the VU meter barely notices.
W
- Wow and flutter
- Speed variations in a tape deck or turntable: slow ones (wow) are heard as a wavering pitch, fast ones (flutter) as a roughness. Usually caused by worn belts, idlers, pinch rollers or bearings.
Looking for numbers rather than words? The tape and disc formats table lists widths, speeds, track layouts and sample rates; the questions and answers page gives short answers to common problems.
Sources
- IASA, IASA-TC 04, Guidelines on the Production and Preservation of Digital Audio Objects, 2nd edition, 2009.
- John W. C. Van Bogart, Magnetic Tape Storage and Handling, CLIR, 1995 (binder hydrolysis, acetate decay, storage).
- Library of Congress, Broadcast WAVE format description, Sustainability of Digital Formats.
- Wikipedia, Tape bias, Dolby noise-reduction system, RIAA equalization, and Wow and flutter measurement, consulted November 2026.